Jet Series Analogue Gauging Probe - AJ/P

The "J" type probes are similar to Standard Pneumatic Probes except that the actuation is by an inbuilt piston. High tip forces are available but as air is vented through a port close to the front of the probe, they have a lower IP rating.

Blank_1

Quick Links
Technical Data Sheet
CAD Drawing
Manual
Knowledge Base

AJ/P Analogue Pneumatic Push Probe - Specification

AJ/P Series
Axial Cable Outlet (LVDT)	A6J/1/P	AJ/1/P	AJ/1.5/P	AJ/2.5/P	AJ5/1/P	AJ/5/P	AJ/10/P
Axial Cable Outlet (Half Bridge)	A6J/1/PH	AJ/1/PH	AJ/1.5/PH	AJ/2.5/PH	AJ5/1/PH	AJ/5/PH	AJ/10/PH
Body Diameter	6h6	8h6
Measurement Range (mm)	± 1.0	± 1.0	± 1.5	± 2.5	± 1.0	± 5.0	± 10.0
Pre-Travel (mm)	0.15
Over Travel (mm)	0.35		0.85		8.85	0.85
Accuracy (% of reading or µm, whichever greater)	0.5, 1.0 µm	0.5, 1.0 µm	0.5, 1.5 µm	0.5, 2.5 µm	0.5, 1.0 µm	0.5, 5.0 µm	0.7, 10.0 µm
Repeatability (µm)	<0.15
Tip Force (N) at Centre Travel ± 20%	1.0 @ 1 bar	0.85 @ 1 bar
Resolution	Dependent on electronics
Temperature Coefficient (% FS/°C)	0.02	0.01

Electrical Interface
LVDT Plugged
Sensitivity¹ (mV/V/mm) ± 0.5%	200	200	133	80	200	40	20
Energising Current (mA/V) ± 5%	3.0	1.8	2.0	2.0	1.8	2.0	1.0
LVDT Unplugged
Sensitivity (mV/V/mm) ± 5%	269	210	150	150	210	105	33
Half Bridge Plugged
Sensitivity¹ (mV/V/mm) ± 0.5%	73.5	73.5	49.0	29.4	73.5	14.7	7.35
Energising Current (mA/V) ± 5%	1.2	1.0	1.0	1.0	1.0	1.2	1.2
Half Bridge Unplugged
Sensitivity ± 5%	88	83	150	150	210	105	33

¹Linearity and Sensitivity error combined does not exceed a total of 0.5%.

Environmental
Storage Temperature (°C)	-40 to +100
Operating Temperature (°C)	+5 to +80
IP Rating	None

Materials
Case	Stainless Steel
Probe Tip	Nylon and Tungsten Carbide
Gaiter	High Grade Polymer
Cable	2 m PUR

Untitled Document

Replacement Gaiters

replacement gaiters

Gaiters can be replaced when damaged. Only pneumatic push probes require gaiter rings.

Part Numbers:

Spring Push		Part Number	Pneumatic Push		Part Number
A6G/1/S	D6P/2/S	205014
AX/1/S	DP/2/S	204851	AX/1/P	DP/2/P	802691
AX/1.5/S		204851
AX/2.5/S	DP/5/S	204894	AX/2.5/P	DP/5/P	802692
AX/5/S	DP/10/S	204860	AX/5/P	DP/10/P	802693
AX5/1/S	DP10/2/S	204860	AX5/1/S	DP10/2/P	802693
	DP/12/S	209562		DP/12/P
AX/10/S	DP/20/S	205906	AX/10/P	DP/20/P	803235

	LE/12/S	209562		LE/12/P	805098
	LE/25/S	205906		LE/25/P	804241

Clamping Collet

For use with all 8 mm clamping shaft sensors. The clamping collet distributes the clamping forces evenly around the shaft. Using the supplied grub screw, the probe can be loosened while holding the collet in place.

Extension Cables Analogue

Extension cables for analogue sensors with 5 pin DIN 240 ° connectors are available for LVDT and Half Bridge types.

Probe Tips

Various probes are available. See Probe tips

Imperial Adapter Sleeves

Adapter Sleeves can be used to increase the body diameter of 8 mm sensors to 9.512 (3/8"). Available in lengths A from 12 to 127 mm.

	Products - Applications - Service Centre - About Us - News - Events	US only
	©Copyright 2012 AMETEK, Inc. All Rights Reserved
	Privacy Policy - Trademarks - Sitemap